unpublished sketch
JeffUsherb posts
subscribe to my Boosty!
I have not been able to use this service for a long time, so if you want to support me, subscribe to my Boosty https://boosty.to/pixelpascal_jeffusherb
2023-01-12 23:41:49 +0000 UTC View Postsubscribe to my Boosty!
I have not been able to use this service for a long time, so if you want to support me, subscribe to my Boosty https://boosty.to/pixelpascal_jeffusherb
2023-01-01 23:00:26 +0000 UTC View Post
:(
Dear patrons!
Unfortunately, I no longer have the ability to withdraw funds from Patreon. I will continue to post content here, but from now, the art r**fle will only be run on Boosty.
If you want to continue participating in the art r**fle and support me - subscribe to my Boosty —> https://boosty.to/pixelpascal_jeffusherb
WIP
This is a small element of future art. The background will also appear here
2022-12-03 23:50:14 +0000 UTC View Post
Old art (pixel style)
Here I present you my old arts in pixel style, soon I will add another series of old arts without pixels
2022-11-23 14:13:53 +0000 UTC View PostCat tree #2
Next, I wrapped the tree with jute rope. (pic 1) Next I will be adding the rope in the process. And the next step was the task of making playgrounds for cats right on the branches. To do this, I ordered pine saw cuts (pic 2), one of which cracked and was screwed not at the very top, but on the table between two whole ones. For fastening, I used self-tapping screws and construction adhesive foam. Shelves should not stagger, otherwise the cat will want to quickly jump off them.
A mount that looks like someone's face (pic 3). A saw cut th...
2022-11-14 10:39:16 +0000 UTC View PostCat tree!
I am making a cat play complex with... an entire room. And perhaps the cat tree will become a chip in it. You can buy similar trees from private traders, but I decided to do everything myself for a minimum of money
First of all, I went to the forest and found a suitable wood element (pic 1), sanding with a knife, grinder (Pic 2) (I use different grit sandpaper. Here, in the classic way, the rough finish is a large grain, the final for the smoothness of a tree is a fine grain). In this post, the result of grinding is not final, I ...
2022-11-06 15:34:45 +0000 UTC View PostHow to build a dog house! My first experience 6
The booth manufacturing process continues. I am making a frankly crooked roof, but so far this is only a draft version.
First, a frame is made according to the size of the booth from above (Pic 1). The roof will be removable. For a frame 80x190cm, bars 70 cm long came up, they are superimposed on each other in the form of a triangle and fastened with a corner, I needed to make three of these, two of them - the beginning and end and one more divides the roof into two parts (not equal) , since I will make a hatch in the part where the bo...
2022-11-02 07:31:09 +0000 UTC View PostHow to build a dog house! My first experience 5
The entrance wall is made of boards, the inlet is along the contour, all the boards are fixed with self-tapping screws. It looks uneven at first, and if you do it completely along the line, then at this stage something even can come out. But this is not the case, so I fixed the boards on the other side with the remnants of the OSB panel (Pic 2), cut it with a jigsaw and sharpened it with a grinder. For evenness, the edges were sheathed again with clapboard (pic 3, you can see the sides in comparison). This step is not obligatory if everythin...
2022-10-29 23:49:13 +0000 UTC View PostHow to build a dog house! My first experience 4
Further, the vertical installation of the bars, choosing their height is according to the dog, so that it would be convenient to stand straight. My bars are measured "on average" as I have all dogs of very different sizes + future frame roof. Attach to corners. (Pic 1)
A wall is being erected, from my lining. On the outside of the lining, a heater is placed in the recess, it can be attached to the adhesive foam, which also adds insulation. And again a layer of lining, thus obtaining an insulated wall.
To give the effect of antiqu...
2022-10-27 16:35:47 +0000 UTC View PostHow to build a dog house! My first experience 3
I am making a foundation frame.
These bars are especially rough treated with tar, because they will stand on the ground and take a hit.
this should be done on the corners or on long self-tapping screws. (Pics 1,2) on top of OSB-3 (Pic 3), and a well of bars in a similar way is in order to accommodate insulation there (pics 4,5) and another OSB on top of the screws. All elements must be treated with tar (pics 6,7)
The result was an insulated foundation - the floor for the booth. Weighty construction.
(Pics 9) Three layers are visi...
How to build a dog house! My first experience 2
So, I'm not going exactly according to my own drawings, but the idea is the same. From the materials I have: timber, lining, OSB-3 panels.
To begin with, I sanded all the dirty and unpolished timber and boards. (Pic 3. Josef is sleeping while I plan the boards and I accidentally covered him with sawdust).
I ordered the clapboard polished, clean and immediately from the package to the case (Pic 6), as well as the osb panels. Osb (Pic) - according to the drawing, I cut two sheets the size of the foundation of the future booth.
It is i...
How to build a dog house! My first experience.
How did the construction of my first booth start and how did it go?
1.The first sketch to understand what I want
2. Next is a series of drawings to understand what materials are needed and how it will look.
The original concept has changed a lot!
speedpaint
art(character without background) will be added above i guess?
2022-09-20 11:00:36 +0000 UTC View Post
